189
Model
XTH 3000-12
XTH 5000-24
XTH 6000-48
XTH 8000-48
Inverter
Nominal battery voltage
12 V
24 V
48 V
48 V
Input voltage range
9.5 - 17 V
19 - 34 V
38 - 68 V
38 - 68 V
Continuous power @ 25 °C
2500 VA
4000 VA
5000 VA
7000 VA
Power Smart-Boost
2500 VA
4000 VA
5000 VA
7000 VA
Power 30 min. @ 25 °C
3000 VA
5000 VA
6000 VA
8000 VA
Power 5 sec. @ 25 °C
3 x Pnom
Load detection (standby)
2 to 25 W
Cos
0.1 - 1
93 %
94 %
96 %
96 %
Consumption OFF/standby/ON
1.7 W / 2.2 W / 14 W
1.8 W / 2.5 W / 20 W
2.2 W / 3 W / 22 W
2.2 W / 3.8 W / 34 W
Output voltage
230 Vac (- 10 % / 0)
Output frequency
50 / 45-65 Hz +/- 0.05 % (crystal controlled)
Harmonic distortion
< 2 %
Overload and short-circuit protection
Automatic disconnection with 3 time restart attempt
Overheat protection
Battery charger 6 step adjustable : I-U-Uo-Equalize-Uo(low)-U(periodic)
Charging current adjustable
0 - 160 A
0 - 140 A
0 - 100 A
0 - 120 A
Input current balance adjustment
1 - 30 A
1 - 50 A
Max. input voltage
265 Vac
Input AC voltage range
Adjustable threshold from 150 to 230 Vac
Input frequency
45 - 65 Hz
Power Factor Correction (PFC)
Yes, according to EN 61000-3-2
General data
Multifunction contact adjustable
2 independent contacts 16 A 250 Vac (potential free 3 points)
Max. current on transfer relay
30 A / 6.9 kVA
50 A / 11.5 kVA
Weight
34 kg
40 kg
42 kg
46 kg
Dimension h x w x l [mm]
220 x 290 x 500
220 x 310 x 500
Protection index
IP 23
Operating temperature range
-20 °C to 55 °C
Ventilation
Forced from 45 °C
Acoustic level
< 10 dB / < 35 dB (with / without ventilation)
Xtender Accessories
Remote control and programming centre
RCC-03
Thanks to its graphic display it provides many understandable
indications on the state of the system.
The remote control memorises and displays the events that
occurred on an installation and so it does anticipate the problems
that might appear.
It gives access to the many adjustable parameters of the Xtender
like the setting of the charge curve of the battery, the programming
of the auxiliary relays or even, among others, to a lot of operation
options.
A place is dedicated to a SD card which will allow the parameters
memorising, the data transfer or the software update.
Battery temperature sensor BTS-01
This sensor enables to accurately adapt the charge thresholds
to the battery temperature memorising, the data transfer or the
software update.
Communication module 3ph and parallel PEM-01
Allows the setting in parallel or the implementation of a 3-phase
system even when only a single-phase source is available
Communication cable for 3ph and parallel
CAB-RJ45-2 (2 m)
Allows the setting in parallel or the implementation of a 3-phase
system even when only a single-phase source is available.
PV OFF GRID CONTROLS
Solar Brochure EXTRA:Layout 1 19/02/2010 13:06 Page 189